Skip to main content
Rad Power Bikes - Import (Aug2023)

How can we help you?

Technical Bulletin: RadMini Stem Riser Clamp Bolt Tightening Guide

The video and instructions in this technical bulletin apply only to RadMini 4 and RadMini Step-Thru 2 bicycles delivered between January 1, 2020 and May 30, 2020.

This article will show you (or your bike mechanic) how to test for adequate stem clamp tightness with a handlebar twist test and how to properly torque the lower 2 stem riser clamp bolts on your RadMini 4 and RadMini Step-Thru 2 delivered between January 1, 2020 and May 30, 2020.

To test and adjust the stem riser clamp bolts and headset tightness on another RadMini, please use the article linked HERE and reference your owner's manual available for download HERE.

If you are not confident in your ability to successfully and safely perform all steps and/or do not have the proper tools, have the work performed or checked by a local, certified, and reputable bike mechanic.

First, perform a handlebar twist test to check that the stem riser clamp is securely tightened.

Handlebar Twist Test

  1. Get the bike ready for testing (and maintenance). Turn off the bike, remove the battery, and press and hold the MODE button to discharge remaining power.
    Turn off bike.png
  2. Check that the handlebar stem quick release lever is closed securely. When the lever is closed, there should be no excess movement between the handlebar stem and the stem riser. If a lever adjustment is needed, open the lever, add resistance by turning the thumbnut clockwise, and close the lever to secure. The lever should require enough force while closing that it leaves an imprint in your palm.
    Check stem quick release lever.png
  3. Perform the twist test.
    1. Brace the front wheel. Stand at the front of the bike and brace the front wheel between your feet and lower legs.
      Brace the bike.png
    2. Try to twist the handlebar. Hold both handlebar grips and push forward with one hand while pulling back with the other hand. Push and pull with about 20 pounds of force with each hand.
      Twist handlebar.png
    3. Ensure the handlebar and wheel stay properly aligned. While a small amount of movement near the stem quick release lever is expected, the handlebar should remain perpendicular to the front wheel and they should not twist independently of each other at the stem riser clamp.
      Perpendicular.png
    4. Repeat the twist test with the opposite hands, pushing and pulling with about 20 pounds of force applied, and verify the handlebar and front wheel are properly aligned.
    5. If you pass the twist test, reinstall the battery, test the bike fully, and have your work inspected by a certified, reputable bike mechanic.
    6. If needed, properly torque both bolts. If the stem riser twists out of alignment, follow the instructions below, to properly torque both bolts.

On any bike, bolts and other hardware can vibrate loose during shipping and over time with normal use. Check your bike components and hardware are tightened securely and/or to recommended torque specifications before each ride and have your bike regularly serviced by a certified, reputable bike mechanic.

If needed, properly torque both bolts following the instructions below.

Properly Torque Both Bolts

You will need:

  • A 6 mm Allen wrench
  • A torque wrench capable of 25 Nm, with a 6 mm Allen bit
  1. Remove and reinstall both lower stem riser clamp bolts, torquing both evenly to 25 Nm.
    1. Use a 6 mm Allen wrench to fully remove both stem riser clamp bolts from the stem riser.
      Remove stem riser bolts.png
    2. Reinstall both bolts.Use a 6 mm Allen wrench to tighten each bolt until the base of the bolt head is snug against the stem riser. You should feel resistance and no bolt threads should be visible at the bolt head.
      Tighten bolts.png
    3. Torque both bolts evenly to 25 Nm. Use a torque wrench to evenly torque both bolts to 25 Nm. Start with the top bolt and tighten one quarter turn, then switch to the bottom bolt. Repeat tightening each bolt one quarter turn, then alternating to the other bolt, until both bolts are torqued to 25 Nm.
      Torque bolts.png
  2. Recheck TWICE that both bolts are properly torqued. Once the torque wrench indicates that both bolts are torqued to 25 Nm, recheck they are properly secured at least two times.
    1. Start at the top bolt and tighten until the torque wrench indicates 25 Nm.
      Torque top bolt.png
    2. Switch to the bottom bolt and tighten until the torque wrench indicates 25 Nm.
    3. Repeat to check that both the top bolt and bottom bolt are torqued to 25 Nm.
  3. Perform the handlebar twist test again. Once the torque on both bolts has been verified at least a total of three times, check the security of the stem riser clamp by performing the handlebar twist test above.
    Twist handlebar.png
  4. If needed, repeat the process to properly torque both bolts. If the stem riser twists out of alignment, repeat the process again, ensuring that both bolts are secured to 25 Nm.
    Torque top bolt.png
  5. If the bike passes the twist test, reinstall the battery, test the bike fully, and have your work inspected by a certified, reputable bike mechanic.

If you do not have the experience, skill, and tools to complete maintenance and adjustment of your bike, Rad Power Bikes highly recommends having a certified, reputable bike mechanic maintain, tune, and ensure the bike is safe to ride.

LOOSE OR IMPROPERLY TORQUED HARDWARE, SUCH AS THE STEM RISER CLAMP BOLTS, CAN CAUSE LOSS OF CONTROL, ACCIDENTS, SERIOUS INJURY, OR DEATH. Check that all hardware is securely tightened securely and/or to recommended torque specifications before each ride.

  • Was this article helpful?